Loading…
Member
Bnystrom, many thanks for your detailed answer!
Dangle and SWGraveler, thank you for your replies. In fact, the less adjustment I will have to do each time I swap the wheels, the better. It is not so easy to find wheels that have a 370 hub, but the 350 are pretty…
Alright, thanks for the hints guys 🙂
All, Many thanks for your replies. I took note of it, and I do not intend to make too many adjustments to get a good shifting when swaping wheels. Now, I will try to get a wheelset with the same hub that I have (DT…
Hi everyone I have a gravel bike (Canyon Grail AL 7 2018) equipped with DT Swiss C 1850 Spline db wheels (SH 11 for the rear wheel). For 100% road rides, I would like to be able to replace these wheels with road wheels.…
Hi Willem, Karst and Dan, I hope it is not too late, I just filled out the google form 🙂. Also, in the question: "Are there any elements in the mentioned kit that could be left out?" it is not possible to select…
TwoWheeler wrote: Link no workee and I can’t edit: https://www.thingiverse.com/thing:3220573/files Hi, what is the recommended error of measurement that the gauge meter should have? I did not find this information in…
Thank you a lot, I managed and it was indeed a tension problem. So now it's better. Only for the low adjustment I am not sure about the L-trim. To make it simple, I will speak in "click". We start from the Top position,…
StuartH165 wrote: Doing this job myself yesterday my top trim adjustment has never been working and I found that I actually need to adjust the trim screw to about half way, then reset the cable under the attachment…
An update, very busy time here so sorry for the delay and thank you for your help. I managed to shift to the last cog at the rear by putting the "shadow" option on off, I was not aware of it. Watching this video , I…
Soooo.. Sorry for the late reply, I could not make it yesterday. So I followed, again, the instruction from the manual linked in my first message. I am asked to put the chain on the largest chain ring and the the…
Hello @CasualGravel , Around 12:00 GMT+1, I will be home and will be able to take some pictures in order to make it clearer. Thank you for your feedback.
Hi everybody, I have an issue with my front derailleur. The way it was adjusted, I could not ride on the large plateau without rubbing to the plate. I tried to finely tune the L and H screws in order to not be touching…
edh wrote: I had same issue (minor rubbing front brake) with 2020 Grail. I talked to the folks at Canyon at showroom and they said ride it and it should go away. It did after first longer ride. Maybe not helpful to…
So, yesterday I went to a bike shop where they spoke English. The technician centered the caliper again, there is a small rubbing, he said it was normal and I should drive for 100 - 150 km and if the problem remains to…
Hmm yes, I see. I did it but it is still rubbing. As it is the first time I have hydraulic brakes, I prefer to see with a workshop even though it is hard to find someone who wants to work on a new bike where I live…
Thank you @CasualGravel for your answer. I was aware of the videos from ParkTool, and most of the time I rely on their work for my bike maintenance. Indeed, while assembling the bike, I pushed the lever without the…
@knl2stl Yes, this is what I think too. I expect my bike to be "ready to ride", even more from canyon. Indeed, my left piston is "more out" than the right one in front, and it seems that the right one is the one pushing…
Thank you guys for your answer. I noticed that also my rear is slightly rubbing, but I guess it is normal when the pads are brand new. @knl2stl the bike is brand new, so are the components. I would be surprise to have a…
Curtis wrote: Is there a possibility that the rotor is not perfectly flat and has a bend in it? I do not see it with the eyes, it is never 100% flat, but you see no movement compared to what a non-flat rotor is usually.